Professional Brake Line Flaring Tool Kit - 45 Degree Single, Double and Bubble Flares Pipe Flare Tool for 3/16', 1/4', 5/16', 3/8' Brake Repair Brake Flaring Tools Brake Line and Tubing Flaring Tool

Angchun Professional Brake Line Flaring Tool Kit for 45 Degree Single, Double and Bubble Flares

• The brake repair brake flaring tools can be used to create 45-degree single, double and bubble brake flares on stainless steel, steel and some soft metal tubing like copper.
• Such as automotive brake lines, transmission cooler lines, fuel lines and others.
• Includes 4 Sets of Die Blocks, suitable for 3/16"(4.75mm), 1/4"(6.35mm), 5/16"(8mm) and 3/8"(9.5mm) Outer Diameter lines.

Warning: The bottom of the tool must be clamped by a vise, make sure the tool is firmly held before use. NOT suitable for use under car.

What U Get

• Brake Line Flaring Tool Body (Vise Mounted);
• 4 Types of Split Dies: 3/16"(4.75mm), 1/4"(6.35mm), 5/16"(8mm) and 3/8"(9.5mm);
• Rotating Handle;
• Long Lever Handle;
• Pipe Cutter;
• Instruction Manual;
• Plastic Suitcase.

Be sure to check that the tool is complete and installed in place before use.

In order to make the tool work properly for a long time, pay attention to the maintenance after each use and remove the stains on the surface.

Easy to Use (Refer to the picture above):

1. Firmly installing the tool to the vise;

2. Cutting tube with the pipe cutter to obtain a flush opening, then remove burrs inside and outside the opening;

3. Pull out the pins of the tool and pull up the clamp, put in half of the die blocks corresponding to the size of the pipe, and then put in the pipe (the pipe opening is flush with the OP.0 of the turntable);

4. Put in the other half of the die blocks of the same size, put down the clamp and push in the pins to lock, and use the T handle to screw until it is still a little loose (make sure that the tube can be pushed when the OP.0 step is aligned);

5. Turn the handle;

6. Confirm that the opening is flush with the end of the die blocks, and use the T handle to fully tighten the dies;

7. Depending on your needs, turn the dial to OP.1 or OP.2 (make sure the head on the side of the dial are accurately aligned with the opening).

• OP.0 + OP.1 for Bubble Flares
• OP.0 + OP.2 for Single Flares
• OP.0 + OP.1 + OP.2 for Double Flares

8. Turn the handle again.

Precautions:

• Wear goggles and gloves before operating the tool, and keep away from others to prevent debris from popping out unexpectedly when turning the handle.
• Therefore, please check that the tool is firmly clamped by the bench vice before use to ensure that it will not move accidentally while working.
• Check that the tool's spring is working properly and that there are no foreign objects on it.

Easy to Make Perfect Flares

1. Select the flat face die, place the tool in a secure vise, tighten the clamps so they do not move.
2. Loosen the clamps, select the desired parting size, insert the die into the rectangular recess in the base of the tool, place the tube between the two halves of the die.
3. Turn the clamps back to their original position, OP.0 is aligned with the port of the tube, push the OP.0 to press it into the port of the tube.
4. Select the desired, select the desired size of reaming cone OP.1, align the tube port, turn the handle and press it into the tube port, then, select the desired size OP.2, repeat the operation, and you can easily complete flare.

Durable, Stable And Accurate Brake Line Flaring Tool

The brake line flaring tool are made of high-quality steel, heat-treated and oxidized for extreme hardness, durability and resistance to damage. Meanwhile, through professional design and rigorous testing, our brake line flaring tool are extremely accurate and stable, and can produce three types of perfect 45-degree flares in a short period of time, which is a professional brake line and fuel line flaring tool!