Your cart is empty.
Your cart is empty.Product Description
- Fits For Bosch Demolition Hammer Models
- DW703 Crosscut Miter Saw
- DW703B2 Crosscut Miter Saw
- DW703B3 Crosscut Miter Saw
This part can be found in the following models: DW703 Type 1 10 MITER SAW DW703 Type 3 10 MITER SAW DW703-B2 Type 1 10 COMPOUND MITRE SAW DW703-B2 Type 2 10 COMPOUND MITRE SAW DW703-B2 Type 3 10 COMPOUND MITRE SAW DW703-B3 Type 1 10 COMPOUND MITRE SAW DW703-B3 Type 2 10 COMPOUND MITRE SAW DW703-B3 Type 3 10 COMPOUND MITRE SAW DW703-BR Type 3 10 MITER SAW
PRODUCT DESCRIPTION：
Parts Number 393960-00 (39396000) Saw Handle
A cam lock miter handle with detent override delivers quick and accurate miter angles.
The rear guide roller kit is manufactured from high-quality raw materials and well-tested by the manufacturer, which has high wear resistance and provides a longer life
- Includes (1) 393960-00 Handle
- New, Bulk Packed
- Replacement Part # 393960-00
- Consult owners manual for proper part number identification and proper installation
- Please refer to list for compatibility
- Compatible with the following: DeWALT: DW703 Type 1, DW703 Type 3, DW703-B2 Type 1, DW703-B2 Type 2, DW703-B2 Type 3, DW703-B3 Type 1, DW703-B3 Type 2, DW703-B3 Type 3, DW703-BR Type 3 Miter Saw
i8adodofly
Reviewed in the United States on April 23, 2025
Be aware that power cord hole on the handle is SMALL. The cord relief bushing does not fit on this item.If you keep it means you have learned to live with it.
Susan Betts
Reviewed in Australia on January 21, 2024
Easily fitted and makes the saw look like new. Works well.
Customer
Reviewed in the United States on January 17, 2024
I have a DW703 type 3 saw and this handle is not correct, even though it is supposed to be for that model. it is too long and the notch for the electrical cord is incorrect.
cmg91
Reviewed in the United States on May 6, 2023
Bought for my DW705. Had to retrofit as lower back is enclosed where OEM is open. As I got deeper into it, turns out that was not my only hurdle. The internal hole that secures bottom to saw was not close to lining up. Had to abandon. Did not want to drill & tap due to proximity to OEM hole being so close. Strain relief boot doesn’t fit. When I put the screws through the two halves into saw frame, they would not come together completely. Could be the cord clamp inside? Will not use carry handle. Not confident it will hold up as there’s a little bit of “slop” now. Buyer beware.
BobP
Reviewed in the United States on February 1, 2023
It’s decent, lighter eight than oem that fell apart . Make sure you take a pic of wire layout before you take everything apart.
John C
Reviewed in the United States on January 28, 2023
I had two issues with this replacement part. The inlet for the power cord did not match the original handle which included a boot. This replacement inlet had a smaller diameter. In order to use it I would have to either remove the boot or buy a different boot with a smaller diameter. Additionally 2 screw holes were bigger than the original which would require me to source different screws that would fit the replacement part. In the picture, the original is on the right, and the replacement is on the left.
NJ Janis
Reviewed in the United States on October 29, 2022
A few of the screw holes were a diff size compared to original handle. I had to use a diff size screw to secure the handle.
Recommended Products
$463.99
$ 99 .00 $99.00